Home

Site Map    FAQ
Full Brochure List
Distribution Amplifiers
Field Strength Meters
Frequency Counters
Frequency Dividers
Frequency Standards
Function Generator
GPS Amplifier/Splitter
GSM Products
Misc. Products
Multimeter 6.5 digit
Oscillators
Phase Noise Testing
Power Amplifiers
Power Supplies
Protek Products
Redundant Systems
Rubidium Oscillators
Signal Generators
Spectrum Analyzers
Timing Systems
UMTS / GSM Tester
 

SG1640 Signal Generator / GPS Frequency Reference

 

 

SG1640 Signal Generator

Key Features

  • 10 µHz to 1640 MHz continuous coverage
  • Frequency Steps: 10 µHz
  • Internal GPS Synchronized Frequency Standard with UTC aligned 1 pps output
  • Frequency Accuracy better  than  1 x 10-10
  • -40 dBm to +10 dBm 50 Ω RF Output (2-1640 MHz)
  • DC to 398 MHz,  3.3 / 5V CMOS Outputs
  • 10 MHz to 1.6 GHz LVDS Output
  • Low Phase Noise and low spurious outputs
  • RS232 Interface
  • Frequency either CW or frequency sweep
  • Broadband Mixer Included

 

General Description

The SG1640 is a 10 µHz to 1640 MHz signal generator with outstanding frequency accuracy.  The SG1640 has a built in GPS Disciplined frequency standard as its main frequency reference.  Frequency coverage is in three bands; DC to 400 MHz, 400 to 800 MHz and 800 to 1640 MHz.  The frequency can be set with 10 µHz frequency resolution.  Frequency accuracy, when locked to a GPS satellite signal, is typically 1 x 10E-10 short term and better than 1 x 10-12 long term.   Thus the SG1640 never requires calibration as it is locked to the GPS satellite service.

Outputs

There are multiple outputs.  The RF output is a 50 Ω,  2 MHz to 1640 MHz output.  This output can be adjusted in amplitude from +10 dBm to -40 dBm.  Logic outputs include a DC – 398 MHz CMOS output that can be set to either 3V3 or 5V output levels.  Dual LVDS/PECL outputs give > 300 mV p-p output level from 10 MHz to 1640 MHz.

Frequency Standard for Free!

The SG1640 has its own GPS synchronized frequency standard (requires GPS antenna – supplied). This GPS Synchronized timebase is available as a 10 MHz output on the rear panel.  This output can act as a laboratory’s frequency reference since it is locked to the global positioning service’s set of satellites.  Accuracy is 1 x 10-10 in the short time (< 1 sec) and as good as 1 x 10-12 in the long term (> 1 week).  This 10 MHz output can be connected to the PTS50 or DA series of distribution amplifiers to synchronize a complete workshop or factory.  Thus all the instruments in an entire factory can be synchronized by the SG1640.

Other Features

The SG1640 also has a general purpose, non-dedicated mixer available via BNC front-panel connectors.  RF and LO inputs are from 4.5 MHz to 2 GHz.  Filtered IF output bandwidth is 4.5 MHz to >350 MHz, with -20dBm RF input and -10 to 5dBm LO input sensitivity.  The conversion gain is 0 to -3.5 dBm conversion gain with +14  dBm damage level.

Front Panel Control and Serial Communication

The unit can be controlled via front panel keys with readout on a 20 x 4 character LCD display.  The unit can also be controlled by a RS232 interface (USB optional).  The internal GPS receiver also has its own RS232 interface allowing monitoring of all its settings and functions, such as the number of satellites tracked, etc.

Case Styles

The SG1640 is available in either a bench case or a 19" rack mount case.  The functions remain the same for both cases, although there is more space inside the 19" rack mount case for options.

Click here for the SG1640 Brochure